Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
We have stumbled upon the article pertaining to Installing A Bathtub directly below on the internet and thought it made sense to share it with you in this article.
Mounting a bath tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately difficult job. If the old bathtub is readily obtainable, the task can relocate speedily; if you have to open a wall surface to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will certainly need a helper to move out the old tub as well as embeded in the new one. Make certain you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your shower room if you have already acquired a new bathtub as well as do not require to change the setup of your previous water system pipes.
Your devices and product checklist must consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome as a result of the limited access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will originate from the pipes. When the supply pipes have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Tub
Making use of the two wood boards under its feet, position the bathtub in the called for position. The wood boards are valuable in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the level checks out level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Turn on the supply of water and also inspect all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the bathtub needs to wait till the bath tub has been used at least once as this will settle it into its final placement.
Preparing for the Installment
To start with, the sustaining structure supplied with the bath needs to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the activity experienced when the tub is in use. The sealant can break relatively early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that content on How to Install a Bathtub while doing a search on the internet. Enjoyed reading our piece? Please share it. Let others find it. Bless you for your time. Visit us again soon.
Need urgent plumbing repairs? Call. Report this page